當過濾器的壓差達到預設值時,將開始自動清洗過程,此間凈水供應不斷流,清洗閥打開,清洗室及吸污器內水壓大幅度下降,通過濾筒與吸污管的壓力差,吸污管與清洗室之間通過吸嘴產生一個吸力,形成一個吸污過程。同時,電力馬達帶動吸污管沿軸向做螺旋運動。吸污器軸向運動與旋轉運動的結合將整個濾網內表面*清洗干凈。整個沖洗過程只需數十秒鐘。排污閥在清洗結束時關閉。過濾器開始準備下一個沖洗周期。
全自動不銹鋼自清洗過濾器由電機、電控箱、控制管路(包括控制閥和壓差變送器)、主管組件、濾芯組件、不銹鋼轉刷、框架組件、傳動軸、進出口連接法蘭等主要零部件組成。
設備特性
電控箱和控制管路構成過濾機的控制部分,用于實現自動清洗排污過程。
過濾介質由濾筒內側進入,經過多層過濾后,液體中的固體懸浮物被截留在濾筒內壁,因污物逐漸增多造成過濾機進出口壓力差增大,全自動自清洗過濾器當壓差達到設定值( 0.01-0.10Mpa )時,排污吸嘴轉至某一濾筒下方,同時排污閥打開,造成該濾筒內的壓力急劇下降,此時濾筒內外壓差迅速增大,筒外凈水對該濾筒進行強力反沖洗,瞬間即可將濾筒內污物*清洗干凈,然后排污嘴轉至下一濾筒進行反沖洗,直到各個濾筒均清洗干凈, 全自動自清洗過濾器壓差恢復到設定狀態。